Description
NE77 is one of the range of architectural films from Coverstyl that recreates the natural look of otherwise expensive materials.
NE77 Eggshell Silk Soft Touch Colour Collection Primary Range
Per Meter
View Our Coverstyl Collections
Visit Architextural
NE77 – Eggshell – Silk – Soft Touch
Coverstyl incorporates hundreds of patterns, all in stock and available by the meter.
The range includes marble, stone, wood, solid colours, metallic, glitter, fabric, and leather patterns.
Use them for decoration and refurbishment.
The flexible films are simple to use.
They make it easy to apply on any furniture shape.
Rated A+ on VOC tests (indoor emissions), as well as being UV and fire-resistant.
Warranty -: 10 years
Application Temperature -: From +12°C to +38°C
Storage -: from +5°C to +30°C : 3 years
Length -: Up To 50M
Width -: 1220 mm
Primer/Primer + -: Yes
Kraft Paper Release Liner -: Yes
Stretchable -: No
Calendared Polymeric -: Yes
Interior Installation -: Yes
Outside Installation -: No
UV-Resistant -: Yes
Permanent Air Release Adhesive -: Yes
Finish: Silk Soft Touch
Thickness -: 220 µm
Scratch-Proof -: High
Suitable Surfaces
Coverstyl Interior Films work on various surfaces like paint, varnish, and laminate.
NE77 has a strong sticky adhesive that sticks well to most surfaces.
NE77 also has air channels to help avoid air entrapment and bubbling.
Like smooth plaster, porous surfaces need extra care because they provide good adhesion.
For surfaces such as these, the use of Primer Plus primer is essential.
For surfaces that need particular care and attention before installation include unsealed concrete.
PVC films and metals that can corrode such as copper will be less suitable for the product.
Smooth surfaces like glass or metal stick best and look nicer.
Slightly textured surfaces offer good adhesion.
Texture may be visible in some finishes.
Heavily textured wallpapers, brick, and concrete block surfaces won’t provide full adhesion coverage.
The texture of the surface will show through the film.
Paints now contain fewer VOCs and additives that make them easy to clean.
These changes may affect how well the adhesive sticks to the painted surface.
Before installing NE77, clean the area with Isopropyl 70/30 to improve the bond.
Thorough cleaning is necessary for vinyl wrap installation.
The use of Primer Plus primer will also help to overcome any adhesion issues.
You can also use thin test strips on the area where you’re applying it to improve adhesion.
This will help you determine what steps to take next, like using a primer.
Adhesion
Before you apply the Interior Film, make sure to repair any holes or chips.
Thoroughly clean the surface with Isopropyl 70/30 Alcohol Rubbing Gel Spray.
Use a microfiber cloth for best results.
Paint or primer needs to be fully cured.
PM04 primer needs at least 2 hours to cure.
A primer coat needs to be applied and fully cured on porous surfaces.
Certain types of MDF grades are very porous, which means they might need more than one coat of paint.
This depends on how well the surface absorbs the paint.
You can also sand roughen MDF, wood, Melamine, and plastics to help them stick better.
Surface Preparation
Damaged areas with holes and chips need to be repaired before applying the Interior Film.
Clean the application surface thoroughly with an Isopropyl 70/30 Alcohol Rubbing Gel Spray using a microfiber cloth.
A primer coat needs to be applied and fully cured for porous surfaces.
Some very porous surfaces such as certain MDF grades may require more than 1 coat depending on the absorbency of the surface.
MDF, Wood, Melamine, and low surface energy plastics can be roughened up with sandpaper to aid adhesion.
Application
The recommended application temperature for NE77 is between 12ºC and 38ºC.
Cut the film to size with a minimum of 25mm extra on all sides for trimming.
Use a squeegee with a felt to smooth out the initial point of contact.
Align the Interior film with the application surface and pull off a maximum of 300mm of liner.
Then starting in the center, squeegee the film down using overlapping strokes.
Remove another 300mm of liner.
Repeat this process until the application surface is completely covered.
Be careful to apply the film just once.
Moving it again and again can make the film separate.
Stretching of the film can cause colour and pattern variation.
Squeegee the entire area again to ensure 100% adhesion.
Using a hot air gun will help ensure 100% adhesive contact and improve the bond.
If air is trapped causing a bubble during installation, strip back the film gently, then reapply with the plastic applicator.
Very small air bubbles can also be released by pricking the bubble with a pin.
Likewise, if you press out the entrapped air by moving your thumb toward the puncture hole.
Primer
We recommend Primer for the following -:
Gypsum Plasterboard.
Calcium Silicate Board.
Concrete.
Painted Walls.
Stone.
Wood.
Melamine.
Polyester Coated Laminates.
Plastisol Coated Metals.
MDF and low surface energy plastics such as Polypropylene and Polyethylene.
A primer will also help prevent issues in the film’s most stressed areas.
These areas are prone to heat and stretching during the application process.
Furthermore Doors’ edges and tops, curved surfaces, corners, and overlapping joints need this treatment.
LX PM04 Primer was made for PVC films, especially for connecting joints.
In addition, it works well with wood, gypsum, etc.
In addition multiple coatings are recommended for very porous surfaces.
Eggshell
Average rating: 0 reviews Like this:
Like Loading...
Related