Z3421C Vintage Leather White 2D Decal Decor Vinyl Wrap NEW

Description

The Decal Decor Z3421C is one out of the range of architectural films, that recreate the natural look of expensive materials.

Z3421C Vintage Leather White 

Per Meter

View Our Decor Decal 2d Vinyl Wrap Collection

Visit Architextural

Z3421C – Vintage Leather White – 2D Decal Decor

All Décor by Decal is a PVC free architectural film that allows installers to give new atmospheres and new sensations to interior spaces by replicating the appearance of natural and more expensive materials.
Transform commercial and residential spaces with choice of aesthetically pleasing and modern pattern designs, including wood, cement, stone, metal, and leather finishes.
Complying with REACH regulations

Warranty: 10 years.

Storage: from +5°C to +30°C : 1 years.

Applications: Ceilings, Doors, Furniture, Lobbies, Elevators, Partitions, Walls

Length: One Meter

Width: 1220mm.

Primer/Primer + : Yes

Adhesive Type: Acrylic based high tack

Adhesive Colour: Clear

Removability: Permanent

Stretchable: Yes (Limited For Thermoforming Recommended On 2D)

Film Type: Polypropylene (PP) PVC free

Interior Installation: Yes Flat Surfaces Only

Outside Installation: No

Finishes: Leather

Thickness: 100 – 200 µm

UV Resistant: Yes

Moisture Resistant: Yes

Suitable Surfaces

Decal Decor 2D Interior Films work on various surfaces (2D).

Z3421C has a strong sticky adhesive that sticks well to most surfaces.

Z3421C also has air channels to help avoid air entrapment and bubbling.

The use of Primer Plus primer is essential.

Surfaces that need particular care and attention before installation include unsealed concrete.

PVC films and metals that can corrode such as copper will be less suitable for the product.

Smooth surfaces like glass or metal stick best and look nicer.

Slightly textured surfaces offer good adhesion.

Texture may be visible in some finishes.

Heavily textured wallpapers, brick, and concrete block surfaces won’t provide full adhesion coverage.

The texture of the surface will show through the film.

Before installing Z3421C , clean the area with Isopropyl 70/30 to improve the bond.

Thorough cleaning is necessary for vinyl wrap installation.

The use of Primer Plus primer will also help to overcome any adhesion issues.

You can also use thin test strips on the area where you’re applying it to improve adhesion.

This will help you determine what steps to take next, like using a primer.

Adhesion

Before you apply the Interior Film, make sure to repair any holes or chips.

Thoroughly clean the surface with Isopropyl 70/30 Alcohol Rubbing Gel Spray.

Use a microfiber cloth for best results.

Paint or Primer needs to be fully cured.

PM04 primer needs at least 2 hours to cure.

A primer coat needs to be applied and fully cured on porous surfaces.

Certain types of MDF grades are very porous, which means they might need more than one coat of primer.

This depends on how well the surface absorbs the primer.

You can also sand roughen MDF, wood, Melamine, and plastics to help them stick better.

Surface Preparation

Damaged areas with holes and chips need to be repaired before applying the Interior Film.

Clean the application surface thoroughly with an Isopropyl 70/30 Alcohol Rubbing Gel Spray using a microfiber cloth.

A primer coat needs to be applied and fully cured for porous surfaces.

Some very porous surfaces such as certain MDF grades may require more than 1 coat depending on the absorbency of the surface.

MDF, Wood, Melamine, and low surface energy plastics can be roughened up with sandpaper to aid adhesion.

Application

The recommended application temperature for Z3421C is +15°c

Cut the film to size with a minimum of 25mm extra on all sides for trimming.

Use a squeegee with a felt to smooth out the initial point of contact.

Align the Interior film with the application surface and pull off a maximum of 300mm of liner.

Then starting in the center, squeegee the film down using overlapping strokes.

Remove another 300mm of liner.

Repeat this process until the application surface is completely covered.

Be careful to apply the film just once.

Moving it again and again can also make the film separate.

Over stretching of the film may cause colour and pattern variation.

Squeegee the entire area again to ensure 100% adhesion.

Using a hot air gun will help ensure 100% adhesive contact and improve the bond.

If air is trapped causing a bubble during installation, strip back the film gently, then reapply with the plastic applicator.

Very small air bubbles can also be released by pricking the bubble with a pin.

Likewise if you press out the entrapped air by moving your thumb toward the puncture hole.

Primer

We recommend Primer for the following -:

Gypsum Plasterboard.

Calcium Silicate Board.

Concrete.

Painted Walls.

Stone.

Wood.

Melamine.

Polyester Coated Laminates.

Plastisol Coated Metals.

MDF and low surface energy plastics such as Polypropylene and Polyethylene.

A primer will also help prevent issues in the film’s most stressed areas.

These areas are prone to heat and stretching during the application process.

Furthermore Doors’ edges and tops, curved surfaces, corners, and overlapping joints need this treatment.

LX PM04 Primer was made for PVC films, especially for connecting joints.

In addition, it works well with wood, gypsum, etc.

In addition multiple coatings are recommended for very porous surfaces.